老司機考不過科目二,那么這腳力是一項非常重要的基本功,近期的話有一些師傅講啊,怎么解決冬季啊,這個膩?zhàn)永锩嬗幸恍┬F(tuán)啊,批刮手感不順滑這樣一個問題,今天我們來給大家分享一個正確的一個攪拌方法,我準備了我們的膩?zhàn)臃?我們的清水和我們的電動攪拌器,好，接下來給大家演示一下；

　　As an experienced driver who cannot pass subject two, foot strength is a very important basic skill. Recently, some masters have talked about how to solve the problem of small lumps in the putty during winter, which makes the scraping feel not smooth. Today, we will share with you a correct mixing method. I have prepared our putty powder, our water, and our electric mixer. Alright, let me demonstrate it to you;

　　擰的是師傅在工地上的一個攪拌方法啊,首先我們來看一下水,那么我們加水的話是一次一次加夠啊,一次加夠水,然后來加粉,我們攪拌完以后呢,可以看到我們的粘稠度呢,也基本上達到了我們的一個要求,但是的話呢,我們的分散功率、攪拌機功率也是夠的哈,攪拌機功率夠,攪拌時長足夠啊,加水量也足夠,但是我們看一下會出現什么問題,可以看到，可以明顯的看到啊,這就是我們師傅反映的小膠團,沒有溶解的小膠團在里面,那么這上墻以后會發生什么情況,我們得給大家看一下,來,拍一下,那么我們可以明顯的看到啊,這個就是在工地現場支付反饋比較多的,沒有溶解的小焦團,并且由于里面的助劑沒有完全溶解,所以說導致我們的批刮手感是不太好刮的,來，我們?cè)偈找幌?看看還是不是會有啊,刮起來是非常難刮的啊,去看一下這里，這里這里,你看里面還有未溶解的小膠團啊,再收一下,好,那么這種粒子挖出來,給我們后續的施工會造成多不方便。

　　This is a mixing method used by the master on the construction site. First, let's take a look at the water. If we add enough water at once, then we add the powder. After mixing, we can see our viscosity, which basically meets our requirements. However, our dispersing power and mixer power are also sufficient. The mixer power is sufficient, the mixing time is sufficient, and the amount of water added is also sufficient. But if we look at what problems will occur, we can clearly see that this is the small gum clusters reflected by our master. There are undissolved small gum clusters inside. So what will happen after we put it on the wall? We need to show everyone, come on, take a picture, so we can clearly see that there are many payment feedbacks on the construction site, and there are no dissolved small coke clusters, And due to the incomplete dissolution of the additives inside, our scraping feel is not very good. Let's take another look and see if there are still any issues. Scratching is very difficult. Take a look here, here, and here, you can see that there are still undissolved small clumps inside. Take another look, then digging out these particles will cause inconvenience for our subsequent construction.

　　那么怎么樣來避免這個問題呢,我們接下來展示一下如何正確的攪拌,統一包灰啊,換個攪拌方法,那么這種情況就可以避免,那么我們現在給大家展示一個啊,比較好的一個攪拌方法,粉還是一樣的粉哈,那我們現在開,那么我們看一下我們的水灰比,是一個什么樣的一個比例,啊,還要再加,粉一定是沒過水的哈,粉一定是沒過水的,我們來攪出來看一下狀態,那么這是我們現在一個狀態啊,我們的是比較稠的,這種狀態的話呢,不要著急哈,我們是這一步的主要目的,是為了讓我們里面的助劑完全分散。

　　So how can we avoid this problem? Next, let's show you how to mix correctly, uniformly package the ash, and change the mixing method. This situation can be avoided. Now, let's show you a better mixing method. The powder is still the same. Let's turn it on now. Let's take a look at our water cement ratio, what kind of ratio is it, and we need to add more. The powder must not have gone through water, and the powder must not have gone through water. Let's mix it out and see the state. This is our current state, which is relatively thick. Don't worry, we are the main focus of this step. The purpose is to completely disperse the additives inside us.

　　那么在這種狀態下呢,我們的師傅可以接下來做什么呢,接下來繼續加調到你比較喜歡的一個狀態,來，我們繼續加水,那么繼續加水以后呢,就調到了我們師傅個人喜歡的一個這樣的一個濃稠度,那么接下來我們上墻去看一下效果,那么現在的話呢,就是按第二種攪拌方法攪拌出來,來我們?cè)賮砜匆幌?來我們拉近了看一下哈,那么通過這種先比較加水量比較少,把小料分散,助劑分散,然后再加水?dāng)嚢璧轿覀兿矚g的濃稠度,這樣一個攪拌方法的話,可以看到啊,我們的膩?zhàn)庸纹饋淼氖指?還有我們的一個表現效果都是非常 OK 的,那么如果你遇到了膩?zhàn)邮┕な指胁豁樆?有可能這樣的一個問題,可以采用我們這種攪拌方法試一下。

　　So, in this state, what can our master do next? Next, we will continue to add water to a state that you prefer. Then, we will continue to add water. After adding water, we will adjust it to a viscosity that our master personally likes. Next, we will go up to the wall to see the effect. Now, we will follow the second mixing method to stir it out. Let's take a closer look. With this mixing method, we can mix the small materials and additives with less water first, disperse them, and then add water to stir them to a viscosity that we like. You can see the texture and texture of our putty when scraped. Our performance results are all very good Well, if you encounter a problem with the smoothness of putty construction, it's possible that you can try using our mixing method.